Bead mill for ink

What kind of ink you are producing?Offset ink, gravure ink, printing ink, digital ink, letterpress ink, packaging inkjet, industrial inkjet, commercial inkjet?If the ink is discharged statically.

For inks, the wear on the wearing parts will be less, because the viscosity of the ink itself is relatively high, the oil is oily, and the zirconium bead wear is relatively small.

Zirconia Beads

If the zirconium beads are not strong enough, they are damaged during the grinding process, which is fatal to the dynamic discharge. The dynamic discharge is constantly rotating, which can easily jam the separator and damage the separator; if the separator is replaced, it will not If the zirconium beads are replaced or the zirconium beads are not carefully sieved, the broken beads of the zirconium beads will still exist, so the separator will still be stuck by the broken beads.

Nano Mill

Nano bead mill is a vertical type, which makes nanometers. The reason: not only the rod pins on the rotor but also on the cylinder, it’s perfect to use 0.2-0.3 beads for the bead mill.

Then our bead mill generally uses 0.2, 0.3mm, with static discharge, the screen is 0.3mm, if the beads are 0.2mm, the beads will run out, with 0.2mm beads, the processing accuracy of the bearing seat cannot be guaranteed. Bearings It is oily. In the process of operation, the coaxiality of the interbody is not so standard, so it is not acceptable to use 0.2-0.3mm beads. If the viscosity is low, use the meshless one, and the viscosity will be higher. Yes, it is necessary to bring a screen, the screen may use a gap of 0.05 or 0.1.

Lab Bead Mill

Cone bead mill

Cone bead mill is usually worked in offset ink, screen printing ink, offset printing ink.

Disadvantages: In the cylinder bead mill, the linear velocity is not uniform. The linear velocity of the big head is the highest. When the cone rotates, the linear velocity of the big head is the highest, and the smallest head is the lowest. So when selecting the line speed, Whichever is the highest or the lowest? Line speed has a set value in the industry

If you take the big head as the standard, the small head linear velocity will be too low, which means that this part of the solvent space is equal to waste, and the efficiency is low; if the small head is the standard, the big head is low, the linear velocity will be very high, which will cause wear Intensified, it will also cause the temperature to be too high.

The FLE BEAD MILL is a machine for continuous superfine grinding and dispersing of solids in liquids. It works following the principle of agitator bead mills, where grinding media is accelerated in the grinding tank by an agitator shaft. The energy given to the media is passed onto the solid particles under collision and de-acceleration. Due to the tank being in a horizontal position, the special agitator gives an even activation of grinding media over the whole tank content. 

dyno mill

The following advantages result from this: 

l high grinding capacity; 

l closer grain distribution; 

l less strain on the grinding system; 

Bead Mill is fed in suspension and processed in one passage. The product flow is adjusted by the feed pump, which determines the residence time in the chamber and thus the fineness of the product. Machines with a variable drive system will allow the agitator shaft to rotate at infinitely adjustable speeds. Constant speed machines can also be adjusted by the use of different drive pulleys. Thus the bead mill can be adjusted to give the most efficient grinding for many different products over a very wide speed range. Depending upon the temperature behavior of the product the grinding chamber can either be cooled or heated.

Vertical bead Mill

Operation of bead mill 

These operating instructions are designed to familiarize the user with the machine and its designated use. 

The Bead mill contains important information on how to 0 operate the machine safely properly and most efficiently.

Observing these instructions helps to avoid danger, to reduce repair costs and down-times, and to increase the reliability and life of the machine. The instruction manual is to be supplemented by the respective national rules and regulations for accident prevention and environmental protection. 

The operating instructions must always be available wherever the bead mill is in use and must be read and applied by any person who carries out works on the machine. In addition to the operating instructions and the mandatory rules and regulations for accident prevention and environmental protection in the country and place of use of the machine, the generally recognized technical rules for safe and proper working must also be observed. 

Therefore we kindly ask you for your understanding that changes in the design or of the models of our product range may arise, that are reasonable for the buyer.

Please be advised that no essential change in the function will take place. 

No claims can be derived from the illustrations and descriptions of this operating manual. 

These operating instructions of the bead mill are only applicable to the order confirmation number stated on the cover sheet. This number can also be found on the bead mill nameplate. 

Welcome to check our factory and testing machines by your materials.

Copyright Notice :
This article only represents the author's point of view.
This article is published under the authorization of the author.
Source:

This article address : Bead mill for ink